Most ever online: 47
Guests: 47,
Members: 0
on Wednesday 21 February 2018 - 23:52:15
Chatbox
You must be logged in to post comments on this site - please either log in from the Login box or from here.If you are not registered click here to signup.
small tool to edit 93C46 eeprom written in BascomAVR & VB
Bascom control the 93C46 so we sent data via comport from VB
code will be added later else Goto MCS forum
BASCOM-AVR : overlay - MWS : REPLY
[quote:2a4c555e15]you suggest using waitkey rather than inkey but I don't understand the difference in this context [/quote:2a4c55...
BASCOM-AVR : overlay - MWS : REPLY
[quote:b085bca43b="njepsen"]I am doing what you advised against - is this what you had in mind?[/quote:b085bca43b]
Yes, this is l...
BASCOM-AVR : overlay - MWS : REPLY
Why dont select them when they arrive? It it tudious job to search for the delchar function. I dont get it.
Seriously?
...
»
BASCOM-AVR : overlay - MWS : REPLY
Thanks for the comments chaps. This was an edited version of what i have running, and I do have a 2 sec timeout in the do loop in...
»
BASCOM-AVR : overlay - MWS : REPLY
you also need to check that you do not keep writing in case of spurious data arrives.
and instead of inkey() use waitkey() since ...
BASCOM-AVR : overlay - MWS : REPLY
I did this with the webserver code I created a 250 character string and overlaid the bytes as you have done,
I needed to pull by...
»
BASCOM-AVR : overlay - MWS : NEWTOPIC
MWS,
some time ago you commented in another post about the follies of building a string with string = String + newch...
GPS Uhr Hier mal meine kleine Bastelei mit GPS(Uhr) und Max7219(4x8x8LED)
Vielleicht kann ja jemand was brauchen
»
Befehl Pulsein unklar Hallo,
ich habe mir mit einem ATTiny24 einen doppelten RC-Schalter gebaut (2 Kanäle als Eingang und 8 + 1 Schaltausgänge). Funktioniert soweit. Nur...
»
Atmega328p Zeitintervall passt nicht Gruß in die Runde.
Meine Zeitintervalle passen einfach nicht und ich seh nicht woran das liegen könnte.
Ich nutze den Atmega328p 28DIP, von Haus a...
»
MCS Bootloader aus Beispiel mit ATMEGA644PA Liebe Forumsmitglieder,
ich versuche gerade meinem Bootloader um die Speicherlogic aus den Bascom-Beispielen zu erweitern.
Ich benutzte einen ATME...
CO2 Sensor MH-Z19B auslesen klappt nicht Hallo,
ich versuche den Sensor auszulesen, aber es kommt einfach keine Rückmeldung.
Die erste Zeile in der ISR habe ich nur temporär eingefügt,
um...
Date published: Sun, 26 Sep 2021 06:23:44 +0000 Details
R.I.P Ben Zijlstra
Remembering Ben Zijlstra
We hope that people who love Ben will remember and celebrate his life.
more info at MCS
www.mcselec.com/index2.ph...
»
KaRadio webradio ESP8266
The Dimitris board is available at https://github.com/dsaltas/WiFi-WebRadio
This is a hardware project for Ka-Radio
»
93C46 small tool to edit 93C46 eeprom written in BascomAVR & VB
Bascom control the 93C46 so we sent data via comport from VB
code will be added later ...
»
nRF24L01+ RC Controller This is a RC controller TX & RX unit with nRF24L01+
nRF24L01+ / with PA and LNA for longer range
facts:
TX
1 x potmeter for servo
...
»
RAW lcd Connecting RAW lcd to atmega8
the lcd is 6 digit + time glass
LCD Hour Meter for tractor ,air compressor, ect
the lcd have 4 com pins & 14...
